FEATURED PRODUCT
TEXTROFLASH™ GREEN
DESCRIPTION
Textroflash™ Green is an air and vapor barrier that is a 40 mil thick composite membrane consisting of a hot melt adhesive laminated to a tough spun-bonded polypropylene film with 45% recycled content. A silicone release liner prevents the material from sticking together in the roll and is easily removed for installation. Textroflash™ Green rolls are 50-foot long and are available in widths of 12”, 16”, 18”, 24”, 36”, 48”, 54”, 60” and 72”.
TYPICAL USE
Textroflash™ Green is a complete air and vapor barrier system when adhered to above-grade substrates. Textroflash™ Green has self-adhering properties. Apply horizontally or vertically over the entire surface area following the installation instructions below. The non-asphaltic clear adhesive backing bonds to masonry, gypsum sheathing, concrete, steel and wood substrates.
MATERIAL CONFORMANCE
Textroflash™ Green Air & Vapor Barrier conforms to the following specifications:
- GSA; PBS PCD 07121
- USN; NAVFAC TS-07111
- Federal Construction Guide Spec; FCGS-07111
ADVANTAGES
- Innovative membrane contains 45% Recycled content
- Possible LEED credits toward certification in categories of Energy & Atmosphere (EA), Materials & Resources (MR) and Indoor Environmental Quality (EQ)
- Tough, spun-bonded film aid in preventing tears or post-installation damage
- Self-adhering
- Self-seals around fastener and veneer anchor penetrations
- Easy to install, inspect and repair
INSTALLATION
Surface Preparation:Allow at least 7-day cure time for concrete. Surface must be smooth and dry, free of oils, dirt, loose rust scales or any other materials which might cause poor adhesion. Fill voids greater than 1/4" across with approved sealant or fill material.
Adhesion Promotion:Surface prep as above to receive Textroflash™ Green Vapor/Air Barrier System. Some substrates may require prep with Textroflash™ Green primer or Flex-Flash® adhesive spray. For spray adhesive, shake can before using. Hold can 6-8 inches from substrates and spray with a uniform pattern. Let adhesive develop tack with a few seconds of open time and then adhere Textroflash™ Green with firm compression. When finished with an application, always turn can upside down and spray for two seconds to clear valve and prevent clogging. If adhesive accumulates around nozzle, wipe clear while wet. If dried in valve opening, remove with degreasing solvent.
Application:Apply Textroflash™ Green Air & Vapor Barrier in lengths of 8' or less. Side laps and overlaps shall be a minimum of 3”. Begin installation at base of wall and work upwards. On large vertical surfaces, apply in 8' sections, starting at the lowest point with the higher section overlapping the lower section. Use a roller to firmly press membrane onto surface without air pockets. Sealant should then be applied on top of all laps at 1/8”-1/4” thickness x 1”-1 ½” with a continuous bead of Textroflash™ Green Mastic.
LIMITATIONS
- Some substrates may require prep with Textroflash™ Green primer or Flex-Flash® adhesive spray.
- Do not apply Flex-Flash® adhesive spray or Textroflash™ Green to damp, frosty, or contaminated surfaces
- Cover within 90 days of installation. (Not intended for longer exposure to weather and UV.)
- Ambient temperature where installed shall not exceed 150°F
- For best installation install at temperatures above 32°F.
FLEX-FLASH® ADHESIVE SPRAY WARNINGS AND HAZARDS (Equivalent to 17.4 Fluid Ounces)
Flex-Flash® adhesive spray contains Acetone and Hexane. Extremely Flammable. Use with adequate ventilation. Keep away from heat, sparks, open flame or other ignition sources. Harmful or fatal if swallowed. Do not take internally. If swallowed do not induce vomiting. Contact a physician immediately. Vapor harmful. Avoid inhalation of spray mist or vapors. If overcome, move patient to fresh air. Call a physician immediately. Eye irritant. Avoid contact with eyes and skin. In case of eye contact, flush immediately with water and continue for 15 minutes. If irritation persists, see a physician. For skin contact, wash with soap and water. If irritation persists, call a physician immediately. Contents under pressure. Do not puncture or incinerate container. Do not store at temperatures above 120°F. KEEP OUT OF REACH OF CHILDREN.
CAS NUMBERS: Isobutane/Propane Blend 75-28-5/74-98-6; Acetone 67-64-1; Glycerine Ester of Resin 25038-32-8; Hexane 110-54-3; Block Copolymer 25038-32-8.
Equivalent to 17.4 Fluid Ounces.
VOC INFORMATION: California ARB Consumer Products Category: Web Spray Adhesive. VOC Standard = 55.0%. VOC Content = 54.9%. This product complies with current applicable CARB standard.
STORAGE
Store flashing materials inside at a temperature between 60o F. (15.5o C.) and 80o F. (26.6o C.) If exposed to lower temperatures, restore materials to 60o F. (15.5o C.) minimum temperature before application. Flex-Flash® should be applied when the air temperature is 32o or higher.
*Note: Hohmann & Barnard, Inc. is not responsible for incompatibility resulting from the use of non-H&B mastic and/or recommended primers and sealants.
LIMITED WARRANTY
|
